Clik here to view.
Seen this before....brake pads
My brakes (front) were displaying dust on the rims and starting to squeal very occasionally, so went to change them. At looking at them still on...they looked pretty new, however the top was coming...
View ArticleJackaroo Seats wanted
Hi guys, im looking for a pair of jack seats to bolt into a 2002 rodeo, Perfrably free or cheap. located Perth. many thanks Gavin
View ArticleTech 2 readings with ORPS failed
Last Sunday I replaced one injector and wiring harness and by strange luck I didn't connect Oil rail sensor properly. While test drive got long start, CheckEngine light always on and heaps of...
View ArticleNeed help obtaining a Sleeve removal tool, buying or hiring.
My 4jx1 started mixing oil and diesel, suspected problems with injectors and sleeves. Im just a young bloke who loves his jackaroo and wants it up and running again because they're beasts to drive. I...
View ArticleClutch problems
The clutch on my Jackaroo has stopped working. The pedal went down without disengaging the clutch and having pulled the pedal back up it will no longer go down. Master cylinder has correct level of...
View ArticlePDF Service Manuals
Hi all,A member of one of the US Trooper forums has made these manuals available for download. They are in PDF format and very detailed.To uncompress the archives below you will need to download WinRAR...
View ArticlePerformance upgrades 09 diesel colorado
Hey Guys, I'm just wondering if anyone out there has done a heap of performance upgrades.. except for chips on their 4jj1 3.0 ltr diesel engine as i would like to learn what you can get away with on a...
View ArticleInhibitor Switch
Hi Guys Just wondering if anyone can offer me some assistance in terms of trying to source a 92 Inhibitor Switch for my Jackaroo I have tried genuine Holden Parts and they advise that they do not...
View Articlewater pump 4jg2 engine
Hi, Does anyone know if the water pump off a 4jg2 engine is the same as the one on the 6ve1 engine?
View Article03 workshop manual
G'day everyone, I sm about to change my front wheel bearing but I wanted to know does anyone have a PDF copy of a workshop manual or even just the section about changing the bearings. TIA
View ArticleClik here to view.
Injector Sleeve Repair (Do It Yourself) Step by Step
Hello everyone !! I recently had to do the dreaded injector sleeve seals and it was hard to find all the information and piece it together so I took photos from start to finish listing everything the...
View ArticleChanging front brake pads problems
Hi Thought I would do a simple job and change the front pads on my daughter 2004 rodeo its a 4wd if that makes any difference. Anyway ripped old pads out reset pistons put new pads in. Now the fun...
View ArticleRear Suspension noise RA 07
RA dual cab 2007 has clunky noise somewhere in the rear end on harder bumps sometimes when combined when cornering. Have replaced the shocks and rear shackles and its still there ! Exhaust doesnt...
View ArticleRattling/rolling noise coming from rear of ute
I'm getting a rattling/rolling noise coming from what sounds like the rear of my RA7 Dual Cab. I have looked everywhere and so far replaced the rear cab mounts and rear suspension. I have been...
View ArticleORPS reading and problems
A quick run down first.... I had diesel filling the oil and lots of white smoke.....took to mechanic (big big mistake), they said it would be the sleeves...changed them....found out it would be the...
View Article1999 rodeo 4x4 manual
Hi guys I have just bought a 1999 rodeo 4x4 crew cab 3.2 v6 and am looking for a copy of the workshop manual if anyone has a cope they could send me it help me out heaps
View ArticleOil Rail Pressure Sensor Valve Rebuilding for 4JX1 engine.
Hello, A common problem i have experienced over 3 models with this engine whilst in my ownership has been this part that caused erratic running after a while (hesitation in acceleration and lumpy...
View ArticleStroke a X20SE
Hi guys i have a 97 SWB M7 fronty with a 2ltr X20SE. It has a 86mm Bore 86mm Stroke I see the X22SE has a 86mm Bore 94.7mm Stroke So my question is can i change the crank shaft to stroke my 2ltr out?...
View ArticleTrying to change bearings
Hey everyone I need some help. I am changing my wheel bearing and I have my wheel off and break calliper off as well, I am now having trouble as the wheel keeps spinning so I can undo any more bolts...
View Article